Ati-amplifier-technologies ATP8700 Bedienungsanleitung PDF herunterladen (Seite 29)

BACKLIGHTING

Pressing any button on the A/V PROCESSOR remote

illuminates all the buttons on the remote control for about

5 seconds. The backlight is extended an additional 5 seconds

with any button press while the backlight is on.

Setup Codes

CABLE CONVERTERS

Manufacturer/Brand Setup Code Number

ABC 0003, 0017

Americast 0899

Bell South 0899

General Instrument 0276, 0476, 0810

GoldStar 0144

Hamlin

0009, 0273

Jerrold 0003, 0276, 0476, 0810

Memorex 0000

Motorola 1106

Pace 0237

Panasonic 0107, 0000

Paragon 0000

Philips 0305, 0317

Pioneer 0144, 0533, 0877

Pulsar 0000

Quasar 0000

Regal 0273, 0279

Runco 0000

Samsung 0144

Scientific Atlanta 0017, 0477, 0877

Starcom 0003

Toshiba 0000

Zenith 0000, 0525, 0899

CHECKING THE CODES

If you have set up the A/V PROCESSOR remote by searching

for the codes, for future reference, you may wish to find out

which four-digit code is operating your equipment.

o Find the Four-digit Code for a Device:

1. On the A/V PROCESSOR remote, press the button near the

top of the remote for the type of device you want to control.

2. Press and hold SETUP until the red LED on the remote

blinks twice, then release SETUP.

3. Enter 990. The LED will blink twice.

4. To view the code for the first digit, press 1. After three

seconds, the LED will blink to indicate the first code

number (i.e., 3 blinks = 3). Count the blinks and write

down the number.

5. Repeat step for each of the other three digits. Press 2 for

he second digit, 3 for the third, and 4 for the fourth.

Count the blinks and write down the numbers.

6. To check for the codes of your other components, repeat

steps 1 through 5, but substitute the appropriate key in

step 1 for the new component you are checking.

OPERATION

After you have programmed the remote control for your

equipment, use the following procedures to operate the

components of your home entertainment system:

To Operate a Component That You Have Programmed:

1. On the A/V PROCESSOR remote, press the button near the

top of the remote for the device you want to control

(CBL, AUX, VCR, TV, SAT, CD, or AMP).

2. Aim the remote control at the device and press the POWER

button to turn on the device.

3. Press the buttons that send out the commands you desire.

Note: Some audio/video devices have separate buttons for

POWER ON and POWER OFF. To operate these devices on

he r

emo

te, pr

ess the corresponding device button to turn

the equipment ON and press the POWER button to turn the

equipment OFF.

Please try all the functions of this remote control with your

equipment. The most common functions are labeled on the

emo

te. Ho

ever, some of the secondary functions might be

stored under a button that has a different name from the one

on your original remote control.

SOURCE SELECTION BUTTONS

essing a sour

ce butt

on (VIDEO 1, DVD, etc.) at the bottom

of the remote control performs the following functions:

■ If the A/V PROCESSOR is in Standby mode, powers up

he unit.

■ Selects that source on the A/V PROCESSOR.

Page 29

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Ati-amplifier-technologies ATP8700 Bedienungsanleitung Seite 29

Kommentare zu diesen Handbüchern